In den Warenkorb gelegt

0,00€ 0 Produkte   Einsehen
Zur Kasse

Adafruit

The leaders in Maker electronics, Adafruit, have been manufacturing in the heart of New York City since 2005. Founded by Limor "Ladyada" Fried from her dorm room they have grown to over fifty employees. They offer a huge amount of learning material and tutorials for beginners and experts alike.

Adafruit

Produkte Sortieren nach: Empfehlung Popularität Titel Neueste Preis

Medium Surface Transducer with Wires - 4 Ohm 3 Watt   ADA1785

Turn any surface/wall/table etc into a speaker with a surface transducer. This type of speaker does not have a moving cone like most speakers you've seen. Instead, a small metal rod is wrapped with the voice coil. When current is pulsed through the coil, the magnetic field causes a piece of metal to expand and contract - and if it's pressed against a surface it turns the transducer into a speaker!

16,45€
(inkl. 19% USt zzgl. Versand)

1 übrig

Adafruit Micro servo   ADA169

Tiny little servo can rotate approximately 180 degrees (90 in each direction), and works just like the standard kinds you're used to but smaller. You can use any servo code, hardware or library to control these servos.

6,95€
(inkl. 19% USt zzgl. Versand)

11 auf lager

DHT22 temperature-humidity sensor + extras   ADA385

The DHT22 is a basic, low-cost digital temperature and humidity sensor. It uses a capacitive humidity sensor and a thermistor to measure the surrounding air, and spits out a digital signal on the data pin (no analog input pins needed). Its fairly simple to use, but requires careful timing to grab data. The only real downside of this sensor is you can only get new data from it once every 2 seconds, so when using our library, sensor readings can be up to 2 seconds old.

9,50€
(inkl. 19% USt zzgl. Versand)

2 übrig

Super Bright White 5mm LED (25 Stück)   ADA754

Need some really bright LEDs? We are big fans of these clear white LEDs, in fact we use them exclusively in our kits. They are very bright and have about 25 degree LED beam so they're good for illumination, head lamps, spotlights, etc. They go easily into a breadboard and will add that extra zing to your project.

7,00€
(inkl. 19% USt zzgl. Versand)

15 auf lager

GT2 Alu Zahnscheiben - 20-Tooth 6mm-Belt 8mm-Bore   ADA1252

For precise motion control, GT2 belts and pulleys offer excellent precision at a great price. This pulley is meant for use with GT2 6mm wide belts only - MXL belts will slip due to the different tooth profile.

8,00€
(inkl. 19% USt zzgl. Versand)

10 auf lager

Adafruit Lautsprecher für Steckplatine PCB - 8 Ohm 0,2W   ADA1898

Listen up! This 1.1" (~30mm) diameter speaker is the perfect addition to any breadboard-based audio project where you need 8 Ohm impedance, and have 0.2W or less of power.

2,00€
(inkl. 19% USt zzgl. Versand)

2 übrig

Adafruit Perma-Proto Full-sized Breadboard PCB - Single   ADA1606

Customers have asked us to carry basic perf-board, but we never liked the look of most basic perf: its always crummy quality, with pads that flake off and no labeling. Then we thought about how people actually prototype - usually starting with a solderless breadboard and then transferring the parts to a more permanent PCB. That's when we realized what people would really like is a proto board that makes it easy!

6,95€
(inkl. 19% USt zzgl. Versand)

24 auf lager

Small push-pull solenoid   ADA412

Solenoids are basically electromagnets: they are made of a big coil of copper wire with an armature (a slug of metal) in the middle. When the coil is energized, the slug is pulled into the center of the coil. This makes the solenoid able to pull (from one end) or push (from the other)

11,50€
(inkl. 19% USt zzgl. Versand)

5 auf lager

3 x AAA Battery Holder with On/Off Switch and 2-Pin JST   ADA727

This battery holder connects 3 AAA batteries together in series for powering all kinds of projects. We spec'd these out because the box is slim, and 3 AAA's add up to about 3.3-4.5V, a very similar range to Lithium Ion/polymer (Li-Ion) batteries and have an on-off switch. That makes them ideal for use with 3.3V projects that have a 2-pin JST connector meant for one of our Li-Ion/Poly batteries. (Of course, you can't recharge them like Li-Ion/Polys, so don't try to plug this into one of our Li-Ion/Poly charger boards!)

2,20€
(inkl. 19% USt zzgl. Versand)

26 auf lager

13.56MHz RFID/NFC Bracelet - 1KB   ADA921

This is a blank 13.56MHz RFID/NFC silicone bracelet. The tag contains a small RFID chip and an antenna, and is passively powered by the reader/writer when placed a couple inches away.

4,25€
(inkl. 19% USt zzgl. Versand)

30 auf lager